TL;DR
Get cleaning gear delivered free with Prime
- Fast, free delivery on millions of items
- Prime Video, Amazon Music and more included
- Member-only deals all year
A Hunker report describes a DIY paper towel holder made from PVC pipe and fittings that hangs beneath a garage workbench or can be adapted for another mounting position. The design uses a tee to keep the roll in place and a screw-mounted flange; exact fit and mounting requirements depend on the bench and towel roll.
Hunker has outlined a do-it-yourself paper towel holder made from PVC pipe and fittings that can hang beneath a garage workbench, keeping the roll accessible without taking up bench space. The design, credited to YouTube channel ratherelevated, offers a low-cost alternative to a freestanding holder, though the material provided does not establish a tested load rating or a universal fit for every workbench.
The basic assembly uses a 15- to 16-inch length of 1¼-inch PVC pipe, a matching PVC tee, and a 1¼-inch flange that screws to a mounting surface. The pipe should be measured against the paper towel roll: Hunker recommends adding about 4 inches to the roll’s length so the pipe can reach into fittings at both ends. The tee at one end acts as a stop, while the opposite end connects to the flange.
For an under-bench installation, the report adds a 90-degree elbow and a short, 4- to 5-inch pipe section. The short section fits into a flange attached to the underside of the bench, turning the holder so the roll hangs below it. Hunker says the design can also be adapted to a wall above the bench or to the side or top of a workbench; the needed fittings depend on the chosen position.
PVC can be cut with a hand saw or a pipe cutter. The report recommends sanding and deburring saw-cut edges so the pipe fits into the fittings. It says the assembly can be left unglued because the fittings hold tightly, but suggests cementing some connections for added stability. If cement is used, the tee should remain unglued so it can be removed when replacing the roll.
Freeing Up Garage Workbench Space
The project addresses a practical storage problem in garages and workshops: a conventional countertop holder takes up room and can shift when a user pulls a towel. A suspended roll can keep paper towels within reach while clearing part of the bench for tools or repair work. That benefit depends on the holder being mounted securely and positioned so the roll does not interfere with other tasks.
The materials are ordinary PVC components, and the instructions describe a straightforward assembly rather than a specialized product. For readers who already have pipe and fittings, the cost may be limited to a flange or mounting hardware; the source does not provide a price, total build time, or a comparison with commercially made holders. Its usefulness is therefore best understood as a customizable storage idea, not a verified performance claim.
As an affiliate, we earn on qualifying purchases.
How the PVC Holder Is Arranged
The original Hunker report presents the holder as a garage-organization DIY attributed to ratherelevated on YouTube. Its basic arrangement places the paper towel roll on a horizontal section of pipe. A tee fitting stops the roll at one end, while a flange provides the attachment point at the other. For a holder beneath a bench, an elbow and short pipe section connect the horizontal roll support to a flange mounted overhead.
The design’s dimensions are guidelines rather than a complete measurement plan for every installation. The report gives the pipe diameter and approximate lengths, but the final arrangement depends on the roll’s width, fitting dimensions, mounting surface and available clearance. It also notes that the holder can be repositioned for a wall or bench side, although those configurations may require different connections.
“The holder is designed to keep shop towels “secure and close at hand” while staying “tidy and out of the way.””
— Hunker, describing the project
Fit and Mounting Details to Check
The source does not give a load rating, durability test, exact cost or installation time, and it does not report whether the holder was tested across different bench materials or towel-roll sizes. It also does not specify screw type, screw length or a required number of fasteners. Readers will need to confirm that the flange and mounting surface can support the holder and roll during repeated use.
Although Hunker says PVC fittings can hold together without glue, the amount of force needed to pull them apart and the effect of repeated use are not quantified. The report also does not provide a full diagram or establish that every listed dimension will work with every brand of paper towels. The final fit and stability remain dependent on the materials and installation.
Measure Before Cutting and Mounting
Anyone following the design should first measure the roll and the intended mounting area, then confirm the pipe and fittings fit together before cutting or attaching the flange. Hunker’s suggested starting point is to make the roll-support pipe about 4 inches longer than the roll, with a 4- to 5-inch connecting piece for the under-bench version. Dry-fitting the parts can help check clearance and make sure the roll can be changed by removing the tee.
Before use, the flange should be fastened securely to a suitable surface with hardware appropriate to that surface. The source does not provide further installation testing or a stated follow-up date. Whether this DIY performs well in a particular garage will depend on the fit, mounting and frequency of use.
Key Questions
What materials does the DIY paper towel holder use?
The main parts listed by Hunker are 1¼-inch PVC pipe, a tee fitting and a screw-mounted flange. The version that hangs beneath a workbench also uses a 90-degree elbow and a short section of pipe.
How long should the pipe for the roll be?
Hunker recommends measuring the roll and adding about 4 inches so the pipe can extend into fittings at both ends. The report gives 15 to 16 inches as a suggested length, but readers should check it against their roll and fittings.
Does the PVC assembly need glue?
The report says the fittings can be assembled without glue, but some joints may be cemented for added stability. It recommends leaving the tee unglued so it can be removed to change the roll.
Can the holder be mounted somewhere other than under a bench?
Yes. Hunker says the design can be adapted for a wall above the bench or the side or top of a workbench. The fittings needed may vary with the mounting position.
Source: rss
Halloween Picks
halloween
As an affiliate, we earn on qualifying purchases.
